The Official 2nd Amendment Appreciation Thread

#102
#102
Seaslug said:
Did someone say silencer (or--more correctly--suppressor)? :)

DSCN3467.jpg
Click to expand...

did you buy it complete...or get the supperssor and barrell cut down seperate?
 
#103
#103
vol_in_ar said:
did you buy it complete...or get the supperssor and barrell cut down seperate?
Click to expand...
Built out a BCM lower and bought a complete BCM upper. The barrel is not cut down. It's a factory 14.5" with a pinned muzzle brake/suppressor adapter. The suppressor is shared with my 10.3" that I'll probably post later.
 
#106
#106
wow...Hadn't been in since last July, and they were packed...
wish I could have made the auction, could have probably picked up some good deals
 
#112
#112
DEFENDTHISHOUSE said:
How are you liking Travis Haley's thornnail offset mount?
Nice set up.
Click to expand...
Love it. It's light and low-profile, and it holds the light nice and tight to the rail. It's Haley's design, but they're actually manufactured by Impact Weapons Components, and I've never dealt with a finer company. :good!:
 
#114
#114
SergeantVol said:
All you gotta do is start with the cookbook recommended loads and gradually step it up. Just gotta keep in mind how much pressure you weapon can handle.
Click to expand...

Load for accuracy, not velocity. If you need to hit something harder/farther get a bigger hammer as opposed to swinging the hell out of a smaller one.

If you aren't trying to push it (or do something insanely stupid, like fill your rifle case full of Unique instead of the Varget) and check your brass it's hard to really mess up that bad.
 
#118
#118
vol_in_ar said:
How about starting with the 10.3
Click to expand...
Lower:

Hero Gear custom factory SBR lower receiver
Daniel Defense lower parts kit
Battle Arms Development ambi safety selector
Phase V Tactical EBRv2 extended bolt catch
Geissele SSA trigger
Magpul MOE+ grip
Magpul winter trigger guard
Noveske receiver end plate with QD sling attachment
LaRue mil-spec receiver extension
LMT SOPMOD stock

Upper:

Daniel Defense Mk18 upper receiver group (10.3" bbl with RIS II Mk18 rail)
Daniel Defense bolt carrier group
BCM Gunfighter Mod 4 charging handle
Matech rear sight
KAC taupe front sight
Tango Down QD stubby VFG
CQD sling mount
Surefire M300A in HSP Thorntail SBR Scout mount
EOTech EXPS3-0 HWS
Aimpoint 3x magnifier in LaRue QD mount
Surefire FH556-212A flash hider/suppressor mount
Surefire FA556-212 suppressor
 
#123
#123
Not much of an armory here... my wish list is massive though. My primary piece... Walther p99c AS in 9mm. I love it. Fits me like a glove.

_MG_50682-1.jpg


Have a few .22lr rifles as well (Ruger 10/22 and Savage 29 pump-action). Looking to get an officer's 1911 in the future. Would also love to build an AR 10/.308 AR rifle at some point.
 
#124
#124
Yankee_Vol said:
I'd be interested in the 50
Click to expand...

Go rent one at your local range and shoot it first. You probably won't be so interested afterward. Let's put it this way... If I was running from someone who was trying to shoot at me I'd rather they have a DE 50 and not a 9mm, because my chances of making it out alive have greatly increased. The price of ammo alone is enough to make you not put that gun in your arsenal.
 
#125
#125
Yea, all 3 of my eagles can barely hit paper at 10 yards. So disinterested in them never even took the time to sight them in. Frames are just to large and no real capacity off ammo. I blame training day for making me buy these. They will sell, novelty gun and all of mine were made in Iseral. Now I believe they are made in MN?
 
New posts
You must log in or register to reply here.

VN Store



Back
Top